|
|||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
|
Thread Tools |
September 2nd, 2009, 20:28 | #1 |
Using heavy BBs in a GBB :where is the limit?
This week-end I might use my TM hi-capa 5.1 as my main weapon (or close to it) in an outdoor game.
I have seen posts where people say to use heavier grade BBs in GBB because the physics behind it makes it a great improvement. I have seen 0.25, 0.28 and 0.30 being suggested. I have 0.36g BBs on hand for my sniper rifle. Would these be overkill, useless or would it be even better then using 0.30?
__________________
Team N.A.P.K.I.N.S (Ninjas And Pirates Kommando Infiltration Night-ops Specialists) |
|
September 2nd, 2009, 20:32 | #2 |
overkill, use 0.30 or 0.28.
you will lose quite a bit of range with 0.36. You can try, but you wont get very good results range wise |
|
September 2nd, 2009, 20:35 | #3 | |
Quote:
All depends on your hop-up rubber and your internal set up... |
||
September 2nd, 2009, 20:42 | #4 |
I said RANGE wise Amos.... not accuracy wise
|
|
September 2nd, 2009, 20:59 | #5 |
AK Guru
|
Range indeed. .36s in theory should have better range then .3s IF the hopup can give it the right backspin. Unfortunately stock TM hicapas from what Ive seen dont even have the hopup to properly spin .3s unless you bend the internal arm a bit or replace the rubber. On max hopup my stock 4.3 shoots great with .25s. It has seen a lot of rounds though. .3s are much more accurate but they drop earlier due to lack of hopup.
__________________
|
September 2nd, 2009, 21:21 | #6 | |
Official ASC Bladesmith
|
Quote:
Best was ~140ft kill with my G19 using 0.36g BBs at Rawdon in 2006. 0.30 would be the max I'd say for aiming dead on. I regularly use those in my KSC MK23 (I have Hazard as a witness, 0.28g would pass 150ft before veering off a bit) since I have SIIS ones I don't use in my rifle (because I have bags of he Bastard sniper BBs), and there is literally no fps drop from 0.30g BBs to 0.28g BBs (Bastards that is) according to my chrony testing with spring guns (rifle and pistol). Sorry, the pics are long gone (old pbase account that I had), but check this out: http://www.airsoftcanada.com/showthr...ght=0.30g+90ft Last edited by CDN_Stalker; September 2nd, 2009 at 21:34.. |
|
September 2nd, 2009, 21:39 | #7 | |
Quote:
Replace the bucking with a Firefly rubber One of my buddies did that and his hi-capa was shooting PERFECT with .25bb's with the hop-up off |
||
September 2nd, 2009, 21:52 | #8 |
Official ASC Bladesmith
|
Ya, I only have KSC pistols. The only TM pistol I have is my MK23 springer. Lol
|
September 2nd, 2009, 22:04 | #9 |
I have a stock TM hi-capa 5.1 and these two hop-up rubbers available (and the stock TM of course) :
Nineball : http://shop.ehobbyasia.com/nine-ball...vsr-rifle.html King Arms : http://shop.ehobbyasia.com/king-arms...bb-pistol.html Which one should I install and what weight of BBs would you think it allow me to use effectively?
__________________
Team N.A.P.K.I.N.S (Ninjas And Pirates Kommando Infiltration Night-ops Specialists) |
|
September 2nd, 2009, 22:07 | #10 |
Nineball.
It's much harder and has better airseal. Wash it with dish detergent and warm water. Then let it air dry before installing. Have fun |
|
September 2nd, 2009, 23:47 | #11 |
Le Roi des poissons d'avril
|
Be carefull with dish detergent, it's really hard on soft rubber and silicone.
__________________
Vérificateur d'âge: Terrebonne |
September 3rd, 2009, 00:24 | #12 |
Slow mo.
|
Would "DOVE" soap work? Or something with a moisturizing feature?
|
September 3rd, 2009, 00:51 | #13 |
Le Roi des poissons d'avril
|
I don't know why you would remove all the oil on a valve before installing it. I'm no techy. All I know is that it will be luber later with silicone oil.
So if it has nothing to do with gluing, leaving a little oil on it will not hurt it's installation IMO. If it's too oiled, then rubbing it off might do. Again, I'm stepping in murky water here.
__________________
Vérificateur d'âge: Terrebonne |
September 3rd, 2009, 02:23 | #14 |
I run .3 in all my pistols and it makes a huge difference in both range and accuracy. That's particularly true of my KSC G17 for the aforementioned reasons. I've pulled it several times at outdoor games this summer, and I've gotten several 100+ foot kills with it with little issue. As Stalker said, you just aim higher as you would with a real gun.
I also recomend the Firefly bucking for TM pistols. My TM P226 had very poor range with the stock rubber. With a Firefly, I can also easily hit targets 100+ feet away. Before I was lucky to get 75 feet out using .3. But .25s worked great, but I didn't get the kind of range I get out of my KSC with .3 until I switched rubbers.
__________________
|
|
|
Bookmarks |
Thread Tools | |
|
|