Vsr tightbore

[Shrapnel[Op-For]]

I've been trying to find a 430mm length tightbore for a TM vsr pro. It's going to be used in conjunction with a PSS10 chamber so I need an AEG barrel. I've been doing a lot of searching.. but I just don't know where to look.

[ThunderCactus]

why does it have to be exactly 430mm? Just get one that's close
Check ehobbyasia or redwolfairsoft
Buy a prometheus 6.03 tightbore, they're the BEST

[CDN_Stalker]

Ya, get one that is longer and either cut, clean and deburr it yourself, or get a machinist to do it for you. Is quite easy, as long as you pay attention to what you are doing.

[Skladfin]

exact one for you from the exact same manufacture

http://shop.ehobbyasia.com/upgrade-p...pec-430mm.html

[Shrapnel[Op-For]]

and that will work with the PSS10 chamber? I couldn't even find that one on x-fire

[T-Hell]

Go to Xfire.com and get it there... they have everything for VSR.. not cheap but then again good stuff is not cheap

[ThunderCactus]

Skladfin, that's not an AEG barrel....

Here you go, 420mm, 10mm aint gonna make no diff
http://shop.ehobbyasia.com/prometheu...ort-420mm.html

[Skladfin]

Originally Posted by Shrapnel[Op-For]

and that will work with the PSS10 chamber? I couldn't even find that one on x-fire

X-Fire = PDI

Laylax = Prometheus/Nineball

PSS10 is a Laylax product

my bad as the last one was not an AEG barrel, Below is the one that Prometheus officially recommends to be used in VSRs with their PSS10 chamber:

433mm Type 89/VSR barrel

http://shop.ehobbyasia.com/upgrade-p...89-vsr-10.html

http://www.laylax.com/products/detai...roduct_id=3039

[Crowin]

The PSS10 hopup chamber needs a AEG barrel, You can file the inside of it if your in a pinch to fit the regular barrels. Alot easier to find a proper barrel if you have time, and patience.

[Shrapnel[Op-For]]

Anywhere I can get a 6.01 aeg tightbore long enough? It would have to be around 430mm in length.

[CDN_Stalker]

Go for a 6.03mm, apparently it's more accurate/consistant than 6.01mm. Nutshell, more consistant airflow around the BB causing less 'touching' of the BB on the inner walls.

[Shrapnel[Op-For]]

I've heard that same theory before.. and I've also heard people say to just go for 6.01 for best accuracy.. I guess I'll just have to decide.

On a side note, .36 good bb wieght for 450fps?

[Amos]

6.01 is best for that extra little FPS for places like the Philippines where they run extremely hot guns.. 6.05 is the best for accuracy, 6.03 is a very nice middle point

The most important thing for accuracy is the consistency of the cut, it is is 100% truely 6.0300 all the way through the barrel it will be much better than a barrel that goes 6.0300-6.0399 fluctuating throughout the barrel.

[Shrapnel[Op-For]]

Oh ok, I thought 6.01 meant better accuracy. I think I'll go with 6.03

[CDN_Stalker]

Originally Posted by Shrapnel[Op-For]

I've heard that same theory before.. and I've also heard people say to just go for 6.01 for best accuracy.. I guess I'll just have to decide.

On a side note, .36 good bb wieght for 450fps?

Hell, all last year I ran my M24 at 400fps with 0.20g, and I only used 0.36g Bastards. So yes. Lol