Airsoft Canada
http://triggerairsoft.com/shop/

Go Back   Airsoft Canada > Discussion > Doctor's Corner
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

CA36 Mess

:

Doctor's Corner

Reply
 
Thread Tools
Old August 28th, 2010, 03:28   #1
pilot
 
Join Date: Feb 2010
Location: Edmonton
CA36 Mess

Hello,

I came back this summer to find my Classic Army CA36K to be completely nonfunctional. About ~1000 BBs have been shot through it since I acquired it in June, only been out a couple weekends. I've pinpointed to problem to be in two places:

A.) The gun won't fire most likely due to a motor problem when when a fully charged 1600 mah battery is plugged in all that is heard is a muffled click from the pistol grip, gun does not respond at all besides this. I've included a nifty youtube video below detailing the sound it's making.

B.) A BB is jammed in the hop-up and I can't figure out how to unjam the hop-up. I made the mistake of disassembling my gun hopefully trying to dislodge the BB by removing the barrel, unfortunately some pieces popped out of the hopup. I've included some pictures below of the pieces and the current state of the hop-up unit. I'd ideally hope to reassemble a functioning hop-up and unjam the hop-up.




Youtube video: YouTube- P8280535.AVI


So, I'm gratefully requesting any assistance in rectifying both problem A and B in either order.

Any assistance is greatly appreciated!

Last edited by pilot; August 28th, 2010 at 04:14..
pilot is offline   Reply With Quote
Old August 28th, 2010, 04:18   #2
Windows
 
Join Date: May 2008
Location: Burnaby BC
1st question, what is the voltage on your battery? The CA36 series are known for burning out trigger contacts so you might want to inspect those. If able, see if a 9.6V will turn over the motor. Chances are the spring is compressed and the motor isn't powerfull enough to reset it.
Typically people clear BBs out of hop up units with a plastic unjamming rod. However, seeing as were already past that point the pieces in the pic need to go togeather as such: 1st, take out the rest of the hop up unit by pushing it towards the front of the gun, rotating it 90 deg, and then pull it out to the rear of the gun. Then dissasemble the entire hopup. 2nd place the hopup rubber on the end (with the extra hole and knotches) of the barrel making sure that the thick part is over the hole. 3rd ensure that the little brass ring is sitting just foreward of the rubber. 4th insert that assembly into the main hop up unit untill the beginning of the knotches meet the plastic. 5th Place the hop up bucking(the middle peice in the picture) in the cradle of the peice on the right. 6th insert those peices into the top of the main assembly. 7th starting at the muzzle slide on the large plastic ring with the larger end facing the main assembly making sure that the peices you just put in are under the ring. Finally, snap the c shaped peice (on the left of the photo) onto the knotches in the barrel with the large end pushing up againsed the main assembly.
Windows is offline   Reply With Quote
Old August 28th, 2010, 17:54   #3
Kos-Mos
 
Kos-Mos's Avatar
 
Join Date: Nov 2005
Location: LĂ©vis (QC)
You will also want to remove the barrel group from the receiver before doing all that.

To do so, you have to remove the handguard pin (just like when you install a battery), then remove the 3 screws that go across the receiver and that are hidden by the hanguard.

Then pull forward on the barrel assembly. It will move out about 1/2". You might have to lift/tilt it to completely remove it. DO NOT FORCE ON IT. It goes out fairly easy.
__________________
Quote:
Originally Posted by Drake View Post
Damnit, don't make me add "no discussing temporal paradoxes" to the rules or I'll go back in time and ban you last week.
Kos-Mos is offline   Reply With Quote
Old September 29th, 2010, 12:12   #4
pilot
 
Join Date: Feb 2010
Location: Edmonton
Alright the problems were fixed with the generous help of Cottoni. Solutions to both problems for future reference:

A.) The 8.4v battery I was using did not have enough voltage to cycle the spring, I swapped for a 9.6v from Cottoni and internals are meshing prefectly.

B.) The hop-up had to be replaced after I cracked the syetem pulling the inner barrel out.

Thanks for all your help everyone!
pilot is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Doctor's Corner

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
http://triggerairsoft.com/shop/

All times are GMT -4. The time now is 22:35.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.