|
|||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
|
Thread Tools |
October 3rd, 2007, 17:40 | #1 |
A Total Bastard
|
TM M4 + Magpull Miad = Problem
Just got one of those Magpull PTS Miad grips, very nice and all, but when I throw it on my M4, it misaligns the motor and no amount of adjusting will fix it.. throw on my G27 and works fine.
Anyone else have this problem or a problem with this Grip and can offer a solution or modification to fix? Thanks.
__________________
W1-5 |
October 3rd, 2007, 21:17 | #2 | |
Join Date: Dec 2003
Location: Waterloo, kitchener, guelph, mississauga, north east toronto
|
hmm what brand M4?
__________________
Quote:
|
|
October 3rd, 2007, 21:59 | #3 |
A Total Bastard
|
TM( in title Z ) with a Supposedly Systema SR 16 Knights Metal Body.
__________________
W1-5 |
October 3rd, 2007, 22:29 | #4 |
A Total Bastard
|
my CA m15a4 id fine. Foxtail instaled mine.
|
October 3rd, 2007, 22:30 | #5 |
A Total Bastard
|
hmm, did I get a bad one or does my gun just not like me very much...
__________________
W1-5 |
October 3rd, 2007, 22:35 | #6 |
Check the routing of your motor wires. Make sure they're both run down the same side and that they aren't binding against the body of the motor. I stripped a pinion and a bevel before Colin_S fixed the problem for me...
|
|
October 3rd, 2007, 22:45 | #7 |
A Total Bastard
|
red wire crosses over at the bottom and runs up beside the black then crosses back over the motor, never had a problem with the wires in the G27.
Illusion told me some people had to dremel some of it off and spacer one side to make it sit right, but im not seeing what part exactly or how much.
__________________
W1-5 |
October 3rd, 2007, 23:24 | #8 |
I had to file down my Magpul grip to get it to fit perfect with my G&P. Never had any motor alignment problem at all, just the grip fitting perfectly flush at the top.
__________________
... _________________________________ KJ Works M9 (full metal) KSC Glock 19 KWA Glock 26c G&P M4 CQB-R "It's Go-Go Not Cry-Cry"-Cherry Darling
|
|
October 4th, 2007, 00:06 | #9 |
a.k.a. Silent Souljah
|
mine doesn't screw in a the way on my G&P body either, although the motor alignment sounds ok..... where did you file inside the grip to fit it flush?
|
October 4th, 2007, 00:25 | #10 | |
Quote:
Just go slow, fit the grip, check it, and then file a bit more if it doesn't sit flush - repeat till done. In the end mine fits perfectly flush and tight with no motor issues.
__________________
... _________________________________ KJ Works M9 (full metal) KSC Glock 19 KWA Glock 26c G&P M4 CQB-R "It's Go-Go Not Cry-Cry"-Cherry Darling
|
||
October 4th, 2007, 01:24 | #11 |
A Total Bastard
|
Its def the grip, something off in it, tried it on my other gun and same issue, grinding, tried filling a bit, but to no avail...
__________________
W1-5 |
October 4th, 2007, 23:47 | #12 |
I had to file the inside of my Magpull grip because it didn't fit over the 7mm bushing, but the motor seems normally aligned.
|
|
October 5th, 2007, 21:13 | #13 |
A Total Bastard
|
Not sure, could be the grip, my man Jugglez is sending me out a new G27 grip, same as my old one and im sending the MP one back.. not taking any chances of a replacement not working before next weekend.. I may try another later to see if it was just that grip..
__________________
W1-5 |
|
Bookmarks |
Thread Tools | |
|
|