Gold plated bullet connectors

lokisama · March 21st, 2009, 21:17

They are used mainly for RC helicopters. I've been wondering if I should put them in instead of deans connectors because the space in my crane stock is a little cramped with deans.

Does anyone have any experience with these? any issues with them regards using them in an AEG?

Any info would be appreciated.

LUTNIT · March 21st, 2009, 21:54

Deans are already fairly small compared to large tamiya. As for bullet connectors I have never used them so can't say for sure but the only thing I would be concerned about would be the amount of metal, I know people who tried to use micro deans and they just melted.

lokisama · March 21st, 2009, 23:33

Hmm I see. the bullets do seem a bit more substantial than the micro deans.
Normal deans are installed right now and they do fit but it would be nicer if the crane stock could be adjusted more freely. Right now once its extended, it's difficult to push it back in.

Danke · March 22nd, 2009, 00:30

Are you sure it's the plug? Did you try the heatshrink with the wire coiled around a pen so it's stays springy like a pigtail?

With just the loose pins on the battery you'll really increase the chance of them touching and causing a short.

00nothing · March 22nd, 2009, 01:37

bullet conectors end up taking more space than deans length wise i have them on a few of my rc motors they are nice for ease of swapping motors, but if they are constantly taken on and off they loosen up a lot and will glitch jsut like tamiya connectors over time deans are the best connectors IMO

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

March 21st, 2009, 21:17	#1
lokisama Trader rating Join Date: Oct 2007 Location: etobicoke, ON	Gold plated bullet connectors They are used mainly for RC helicopters. I've been wondering if I should put them in instead of deans connectors because the space in my crane stock is a little cramped with deans. Does anyone have any experience with these? any issues with them regards using them in an AEG? Any info would be appreciated. __________________ Western Arms Infinity 6" Hybrid DX silver Limited Western Arms Infinity 5" Expert KSC MP7A1 KSC USP Match Kimber Warrior [Nova FMU kit] Kimber Gold Combat Stainless [Nova FMU kit]

March 21st, 2009, 23:33	#3
lokisama Trader rating Join Date: Oct 2007 Location: etobicoke, ON	Hmm I see. the bullets do seem a bit more substantial than the micro deans. Normal deans are installed right now and they do fit but it would be nicer if the crane stock could be adjusted more freely. Right now once its extended, it's difficult to push it back in. __________________ Western Arms Infinity 6" Hybrid DX silver Limited Western Arms Infinity 5" Expert KSC MP7A1 KSC USP Match Kimber Warrior [Nova FMU kit] Kimber Gold Combat Stainless [Nova FMU kit]

March 22nd, 2009, 00:30	#4
Danke Prancercise Guru Trader rating Join Date: Oct 2007 Location: Danger Zone	Are you sure it's the plug? Did you try the heatshrink with the wire coiled around a pen so it's stays springy like a pigtail? With just the loose pins on the battery you'll really increase the chance of them touching and causing a short. __________________ Airsoft, where nothing is hurt but feelings.

March 21st, 2009, 21:54	#2
LUTNIT Trader rating Join Date: Dec 2005 Location: Ottawa	Deans are already fairly small compared to large tamiya. As for bullet connectors I have never used them so can't say for sure but the only thing I would be concerned about would be the amount of metal, I know people who tried to use micro deans and they just melted.

March 22nd, 2009, 01:37	#5
00nothing Trader rating Join Date: Jan 2009 Location: Angus, Ontario	bullet conectors end up taking more space than deans length wise i have them on a few of my rc motors they are nice for ease of swapping motors, but if they are constantly taken on and off they loosen up a lot and will glitch jsut like tamiya connectors over time deans are the best connectors IMO __________________

Gold plated bullet connectors

Upgrades & Modifications