What Motor for my set-up?

lurkingknight · February 3rd, 2014, 20:26

infinity hop from reaps?

Chromey · February 3rd, 2014, 20:30

As far as internals, My money goes too Airsoftstore. They have been perfect for all my needs.

After I install the new tappet plate and check my FPS, If needed Ill look at a Lonex.

Should I buy the orange?

I only shoot semi, So high rate of fire is of no interest too me.

pestobanana · February 3rd, 2014, 21:09

Yes that motor will be fine.

Chromey · February 3rd, 2014, 21:24

Quote:

Originally Posted by pestobanana

Yes that motor will be fine.

Thanks, Ill find out when the Tappetplate comes in if I need too upgrade the motor too.

pestobanana · February 3rd, 2014, 21:26

Quote:

Originally Posted by Chromey

Thanks, Ill find out when the Tappetplate comes in if I need too upgrade the motor too.

Wah? Why are you changing your tappet plate lol

Chromey · February 3rd, 2014, 22:21

LOL Good question, No doubt. Its Old and flexes so much that it gets hung up on the piston during the cycle.

pestobanana · February 3rd, 2014, 22:30

Quote:

Originally Posted by Chromey

LOL Good question, No doubt. Its Old and flexes so much that it gets hung up on the piston during the cycle.

How is that possible? Your gearbox has a guide rail for the tappet plate lol

Chromey · February 4th, 2014, 18:06

The flex comes right at the sector gear and sends the tappet plate into the piston.

pestobanana · February 4th, 2014, 18:14

Quote:

Originally Posted by Chromey

The flex comes right at the sector gear and sends the tappet plate into the piston.

There should be a guide rail to prevent that.

ThunderCactus · February 4th, 2014, 18:29

it does happen, the tappet can flex out of that groove. Common when the plate is too wide for the mechbox, jams up front and the back just flexes up and down lol
Most OEM tappet plates are rigid to prevent that, but they break easier. It's a fine balance between flex and rigid

Chromey · February 4th, 2014, 22:12

If you open your gear box you will see that the rail does not cover 100% of the tappet plate, On a G@G M4 V2 gearbox.
So flex at the end can happened on older warn parts.

pestobanana · February 4th, 2014, 22:31

Didn't know that. All of my gearboxes have rails that prevent that.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

February 3rd, 2014, 20:26	#16
lurkingknight "bb bukakke" KING! Trader rating Join Date: Jul 2011 Location: Ottawa	infinity hop from reaps? __________________ I futz with V2s, V3s and V6s. I could be wrong... but probably, most likely not, as far as I know.

February 3rd, 2014, 20:30	#17
Chromey Whiny Attention Whore Trader rating Join Date: Jul 2013 Location: Acton, On	As far as internals, My money goes too Airsoftstore. They have been perfect for all my needs. After I install the new tappet plate and check my FPS, If needed Ill look at a Lonex. Should I buy the orange? I only shoot semi, So high rate of fire is of no interest too me. __________________ B.A. Level 3 Cert.

February 3rd, 2014, 22:21	#21
Chromey Whiny Attention Whore Trader rating Join Date: Jul 2013 Location: Acton, On	LOL Good question, No doubt. Its Old and flexes so much that it gets hung up on the piston during the cycle. __________________ B.A. Level 3 Cert.

February 3rd, 2014, 21:09	#18
pestobanana Squid Porn Superstar, I love the tentacles! Trader rating Join Date: Nov 2008 Location: Richmond Hill and Waterloo, Ontario	Yes that motor will be fine.

February 4th, 2014, 18:06	#23
Chromey Whiny Attention Whore Trader rating Join Date: Jul 2013 Location: Acton, On	The flex comes right at the sector gear and sends the tappet plate into the piston. __________________ B.A. Level 3 Cert.

February 4th, 2014, 18:29	#25
ThunderCactus Not Eye Safe, Pretty Boy Maximus on the field take his picture! Trader rating Join Date: Feb 2007	it does happen, the tappet can flex out of that groove. Common when the plate is too wide for the mechbox, jams up front and the back just flexes up and down lol Most OEM tappet plates are rigid to prevent that, but they break easier. It's a fine balance between flex and rigid

February 4th, 2014, 22:12	#26
Chromey Whiny Attention Whore Trader rating Join Date: Jul 2013 Location: Acton, On	If you open your gear box you will see that the rail does not cover 100% of the tappet plate, On a G@G M4 V2 gearbox. So flex at the end can happened on older warn parts. __________________ B.A. Level 3 Cert.

February 4th, 2014, 22:31	#27
pestobanana Squid Porn Superstar, I love the tentacles! Trader rating Join Date: Nov 2008 Location: Richmond Hill and Waterloo, Ontario	Didn't know that. All of my gearboxes have rails that prevent that.

What Motor for my set-up?

Upgrades & Modifications