Airsoft Canada
https://www.replicaairguns.ca/airsoft

Go Back   Airsoft Canada > Discussion > Airsoft Guns Discussion
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

Rust in the metal part of slide on a KSC Glock

:

Airsoft Guns Discussion

Reply
 
Thread Tools
Old March 5th, 2006, 23:53   #16
PTE. Pyle
 
PTE. Pyle's Avatar
 
Join Date: Oct 2004
Location: delta B.C.
Send a message via MSN to PTE. Pyle
well first off im not the person to tell you how do take the blow back chamber out of your gun. first find somone who can give you direction. after you have it out all the rust remouved and cleaned of all oil i would use tremclad rust paint. you can get it in a small tin at home depot. not the spray use the kind you brush on. then put 1 or 2 coats on. you just want to make sure that you dont put it on to thick or it could inhibbit moving parts. also make sure to not get paint on any plastic or ruber parts it could eat them. graylocks is right though id use 0000 steel wool vs sand paper
__________________
To live is to Die
PTE. Pyle is offline   Reply With Quote
Old March 6th, 2006, 07:18   #17
Greylocks
 
Greylocks's Avatar
 
Join Date: Dec 2001
Location: Gatineau, Quebec (Near Ottawa)
Avoid paint. It may have chemicals in it's composition that could really screw your gun.
Stick with what works.
Sandpaper? May as well use a grinder...

My suggestion is proven with ANY type of gun, airsoft or 'real'.

Pyle... suggesting paint is not wise. Period. Do some research before giving ideas that can cost more than they are worth.
Tremclad, sheesh.
Greylocks is offline   Reply With Quote
Old March 6th, 2006, 13:54   #18
WhatTheWho
 
WhatTheWho's Avatar
 
Join Date: Dec 2002
Location: Edmonton, AB
Quote:
Originally Posted by DannyMac
And also, since it looks all rusted, how do I get down in there? That screw in the middle of the metal you see on the slide there, if I unscrew that does that whole metal piece lift out?
Yes, removing the screw at the rear of the chamber block allows it to come out wholey.

Just be carefull about parts#23 and they can freely slide out the forward nozzle end after removing the entire chamber from the slide.
__________________
"The greatest pleasure in life is doing what people say you cannot do."
WhatTheWho is offline   Reply With Quote
Old March 6th, 2006, 23:17   #19
DannyMac
 
Join Date: Feb 2006
Location: Toronto
Quote:
Originally Posted by WhatTheWho
Quote:
Originally Posted by DannyMac
And also, since it looks all rusted, how do I get down in there? That screw in the middle of the metal you see on the slide there, if I unscrew that does that whole metal piece lift out?
Yes, removing the screw at the rear of the chamber block allows it to come out wholey.

Just be carefull about parts#23 and they can freely slide out the forward nozzle end after removing the entire chamber from the slide.
I can't figure out how to remove this thing. It feels like its stuck in there pretty good I don't want to break anything, how do I pull it out? There's really nothing to push it out by. I've done some searches and can't seem to find anything on how to remove the blowback chamber on the ksc 19?
DannyMac is offline   Reply With Quote
Old March 7th, 2006, 07:01   #20
Greylocks
 
Greylocks's Avatar
 
Join Date: Dec 2001
Location: Gatineau, Quebec (Near Ottawa)
If you do what I said, you wont need to take anything apart except remove the slide.
Greylocks is offline   Reply With Quote
Old March 7th, 2006, 10:07   #21
DannyMac
 
Join Date: Feb 2006
Location: Toronto
Quote:
Originally Posted by Greylocks
If you do what I said, you wont need to take anything apart except remove the slide.
Yeah but all the little crevices and stuff down in there are rusted to hell as well, it's pretty tough to get in there with any leverage with a piece of steel wool. Hmmm maybe I'll try wrapping the steel wool around a q tip or something but as you can see there are some really tight little places in there.
DannyMac is offline   Reply With Quote
Old March 7th, 2006, 19:46   #22
WhatTheWho
 
WhatTheWho's Avatar
 
Join Date: Dec 2002
Location: Edmonton, AB
Quote:
Originally Posted by DannyMac
I can't figure out how to remove this thing. It feels like its stuck in there pretty good I don't want to break anything, how do I pull it out? There's really nothing to push it out by. I've done some searches and can't seem to find anything on how to remove the blowback chamber on the ksc 19?
I remove the chamber block by banging the slide against my hand until it becomes loose enough to grasp with my fingers.
__________________
"The greatest pleasure in life is doing what people say you cannot do."
WhatTheWho is offline   Reply With Quote
Old March 7th, 2006, 19:58   #23
DannyMac
 
Join Date: Feb 2006
Location: Toronto
Quote:
Originally Posted by WhatTheWho
Quote:
Originally Posted by DannyMac
I can't figure out how to remove this thing. It feels like its stuck in there pretty good I don't want to break anything, how do I pull it out? There's really nothing to push it out by. I've done some searches and can't seem to find anything on how to remove the blowback chamber on the ksc 19?
I remove the chamber block by banging the slide against my hand until it becomes loose enough to grasp with my fingers.
Thanks man, I tried that and it worked. I just banged it on a desk a little bit and then it started to pop out a bit then I could grip it and slide her out of there. I found only the surface to be rusted really, the rest of it is all lubed up bigtime.
DannyMac is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Airsoft Guns Discussion

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
https://www.replicaairguns.ca/airsoft

All times are GMT -4. The time now is 20:47.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.