Huang's (Dragon Red Airsoft Outlet) T-1 Micro LT660 Problem

kullwarrior · March 18th, 2010, 02:11

i just got myself a T-1 micro with LT660 Replica mount. The low-level pictinny rail was fine but I need the high riser, when I install it it was not a perfect match, the sight was on an angle. I was like err what ever, I'll just compensate with windage and elevation adjustment. Bigger problemw as the quick release mount, I cannot close it completely, the metal will dig into my upper receiver. (PTW and Prime)
I'm just wondering if anyone has these problems. If you do, what did you do the fix it? Worse comes to worse, I'll just get the LT660 mount, will that work with the replica?

Shirley · March 18th, 2010, 02:20

RS mounts will work on the replica.

I have the same problem with most QD China stuff. Poor rails.

Danke · March 18th, 2010, 02:28

Mine fits all my VFC, TM, and KWA rails with both the low and the Laure mount copy.

Maybe take a close look inside the mount where it meets the rail to see if there's a little burble of material that's causing your problems.

kullwarrior · March 18th, 2010, 02:34

From what I can tell its bad molding of cast metal, I could try slowly sanding it away but I fear it will ruin the integrity of the mount.
How much and which brand of the riser did you bought Hitman?

Shirley · March 18th, 2010, 02:47

Don't have one, but I know they do fit on RS. LT660 goes around USD $100, try ebay. lol

EN SABAH NUR · March 18th, 2010, 02:53

I got mine today too and I have the same problem with the LaRue replica riser. You can disassemble the throw lever and release some of the tension on the spring inside it. Be careful. The spring and washer almost hit me in the eye. It's under a lot of tension.

kullwarrior · March 18th, 2010, 03:43

Quote:

Originally Posted by EN SABAH NUR

I got mine today too and I have the same problem with the LaRue replica riser. You can disassemble the throw lever and release some of the tension on the spring inside it. Be careful. The spring and washer almost hit me in the eye. It's under a lot of tension.

did already, spend about 5 min of dremal, bad cast, bad painting. Honestly My spray paint job attracts less problems. and btw it wobbles a bit, I had to tighten the hex screw to ungodly strength to make it stop wobbling.
As for the riser fitting to optic, its 1mm OFF 1mm!!! so yea you can see through, Optic zero fine like it should be.

nighthitcher · April 7th, 2010, 05:50

sounds good to me

Able1 · April 20th, 2010, 01:42

file down the inner edge on the riser and it will work.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

March 18th, 2010, 02:11	#1
kullwarrior Trader rating Join Date: Jan 2008 Location: Edmonton, AB, Canada	Huang's (Dragon Red Airsoft Outlet) T-1 Micro LT660 Problem i just got myself a T-1 micro with LT660 Replica mount. The low-level pictinny rail was fine but I need the high riser, when I install it it was not a perfect match, the sight was on an angle. I was like err what ever, I'll just compensate with windage and elevation adjustment. Bigger problemw as the quick release mount, I cannot close it completely, the metal will dig into my upper receiver. (PTW and Prime) I'm just wondering if anyone has these problems. If you do, what did you do the fix it? Worse comes to worse, I'll just get the LT660 mount, will that work with the replica? __________________

March 18th, 2010, 02:20	#2
Shirley A-56 aka Mr.Hitman Trader rating Join Date: Nov 2007 Location: Toronto, ON	RS mounts will work on the replica. I have the same problem with most QD China stuff. Poor rails. __________________ CANADIAN AIRSOFT PRACTICAL SHOOTING (CAPS) CAPS DIRECTOR # 0047

March 18th, 2010, 02:28	#3
Danke Prancercise Guru Trader rating Join Date: Oct 2007 Location: Danger Zone	Mine fits all my VFC, TM, and KWA rails with both the low and the Laure mount copy. Maybe take a close look inside the mount where it meets the rail to see if there's a little burble of material that's causing your problems. __________________ Airsoft, where nothing is hurt but feelings.

March 18th, 2010, 02:34	#4
kullwarrior Trader rating Join Date: Jan 2008 Location: Edmonton, AB, Canada	From what I can tell its bad molding of cast metal, I could try slowly sanding it away but I fear it will ruin the integrity of the mount. How much and which brand of the riser did you bought Hitman? __________________

March 18th, 2010, 02:47	#5
Shirley A-56 aka Mr.Hitman Trader rating Join Date: Nov 2007 Location: Toronto, ON	Don't have one, but I know they do fit on RS. LT660 goes around USD $100, try ebay. lol __________________ CANADIAN AIRSOFT PRACTICAL SHOOTING (CAPS) CAPS DIRECTOR # 0047

March 18th, 2010, 02:53	#6
EN SABAH NUR AKA Daniel Ochoa Trader rating Join Date: Oct 2004 Location: Da Snow Belt	I got mine today too and I have the same problem with the LaRue replica riser. You can disassemble the throw lever and release some of the tension on the spring inside it. Be careful. The spring and washer almost hit me in the eye. It's under a lot of tension. __________________ www.papertesseract.tumblr.com "Son. You got a panty on your head" - Hayseed

April 7th, 2010, 05:50	#8
nighthitcher Trader rating Join Date: Apr 2010	sounds good to me __________________ 642-746 certification and 642-812 preparation for 642-825 certification and 642-845

April 20th, 2010, 01:42	#9
Able1 Joeyaglr444 Trader rating Join Date: Mar 2006 Location: Toronto Ontario	file down the inner edge on the riser and it will work. __________________ It's not about the guy who doesn't call his hit. It's about the pants you're wearing and the pants you're team mate is wearing, Is it real multi cam or is it Chinese repro multi cam? I don't know but in the end it's still multicam.

Huang's (Dragon Red Airsoft Outlet) T-1 Micro LT660 Problem

Upgrades & Modifications