VSR10 Laylax PSS10 Hair trigger

[ScooterVauto]

Hi folks.
sure its fun to say you have a hait trigger, try it with a 460 FPS
sniper rifle with no safety hahahaah
OK any one know how to adjust the sensitivty on the pss10 system?
I have googled it and searched through the Doctor section with nothing.
I did answer a VSR hop up question tho
I see a screw and spring but Im not a guesser... Not with this rig anyway
Thanks In advance
SV

[CDN_Stalker]

Originally Posted by ScooterVauto

Hi folks.
sure its fun to say you have a hait trigger, try it with a 460 FPS
sniper rifle with no safety hahahaah
OK any one know how to adjust the sensitivty on the pss10 system?
I have googled it and searched through the Doctor section with nothing.
I did answer a VSR hop up question tho
I see a screw and spring but Im not a guesser... Not with this rig anyway
Thanks In advance
SV

If the VSR trigger assembly is anything like the CA M24 assembly, there would be a screw in the trigger above where you pull with your finger, this would adjust the distance of the trigger pull before sear release, too little, hair trigger, too much, long and hard trigger pull.

[ScooterVauto]

Thanks Stalker, I'll have a boo

[CDN_Stalker]

Originally Posted by ScooterVauto

Thanks Stalker, I'll have a boo

No problem, take a look at it too when you get the chance. Lol

[ScooterVauto]

Hi again.
so the only screw i can find is at the back of the trigger with a spring hooked to it that goes over the top into oblivion.. I did notice a bearing that the trigger is directly attaced to. the trigger moves, pulles the bearing down and a unit attached directly to the sear slips over and releases said sear...
Looks like this is the triggers main advatage, no friction from trigger to sear release.. Check it out
YouTube- Laylax PSS 10 Zero Trigger

thanks again Sir

[CDN_Stalker]

You didn't mention the fact you have a Zero Trigger installed, that's a whole different kettle of fish right there! I thought you were talking about the stock PSS10 (TM VSR) trigger assembly.

[ScooterVauto]

well call it a noob mistake
I should have said Laylax Pss10..
but thank you my good man

[CDN_Stalker]

Well, that trigger assembly is a high performance upgrade, where the stock VSR assembly is much weaker and less well designed. And as a point of reference, PSS10 is for any parts you'd install in a TM VSR, such as springs, pistons, etc. It's a model number reference for the rifle the parts are designed to go with, same as PSS2 is applied to the Maruzen APS2 and CA M24 rifles.

Nutshell, you have a Zero Trigger designed to work with the VSR platform, and is made by Laylax, hence the Laylax PSS10 marking on it.

You are one step away from the noobness status than you were before reading all this. Meaning you are smarter than a noob regarding this info.

[ScooterVauto]

Ahhh clairty is the Key (A single light and all)
Im working an an all Layalx Rig.. (cept for the Promethius 603 and ARS or Guarder hopup rubber)
and now that i looked at the various kit i should have noticed its all PSS10 ..
waahoooo one thing about being a noob, your allowed to make mistakes or miss the obvious hahhahahha

[CJay]

Originally Posted by CDN_Stalker

You didn't mention the fact you have a Zero Trigger installed, that's a whole different kettle of fish right there! I thought you were talking about the stock PSS10 (TM VSR) trigger assembly.

One thing bud. Pss10 is most defo not stock tm marking. Stands for Perfect Sniping System 10 and yeah ur right the 10'is in reference to the vsr10. Laylax do make a sears set to upgrade ur stock tm sears but I don't think they are pss10 marked although I may be wrong haha. Only the zero trigger carries the pss10 markings as trigger mechs go

[ScooterVauto]

For future referance
My VSR10 PRO The Laylax Poster Child
Laylax PSS10 trigger system with Neo piston (90 deg Version) with the little white nipple thing (for now)
Laylax PSS10 Bearing spring guide (enroute)
Laylax 150 spring for VSR
Laylax PSS10 Pro Nozzel (Enroute)
Laylax PSS10 Hopup (Waiting for it to be shipped from Private asc sale)
Guarder AEG black hopup rubber Cut down to Fit Stock TM hopup unit
ARS hopup Rubber (Waiting for Laylax hopup) Eventually
Promethius 603 433mm Tight bore (Waiting for Laylax hopup) Eventually
TM 14mm CCW barrel adapter (Enroute)
Madbul Compressor (Whoop thats a bad boy heheheh waiting for adapter)
TM scope rail
Tasco World Class 3x9 - 40 (better anti fog then the bushnell) with Tasco Aluminum Rings
Looking for a nice sling and Bipod
BDUs -- Urban invisable (Sweats and a loose t-shirt)
that should prevent some of the confusion
Play safe
SV