MP5 Hopup unit

SlippGun · April 28th, 2011, 01:31

Hey all,

I am planning on upgrading my Aftermath Broxa, and I've been reading on here to replace the hopup unit, bucking and barrel.

My problem is, I can not for the life of me find a new hopup unit (since the stock one is not compatible with after market parts?). Everyone says to get a TM one, but I can't find one. I've come across a CA one, would that be okay to go with.

Also, would it be better to pick up a Black Python 6.03mm TB, or a Madbul 6.01mm TB?

Thanks if anyone can help with these slight road bumps.

cjboi · April 28th, 2011, 01:45

TM and ICS would work they're both the same... I thought broxa didn't come with a hop up

SlippGun · April 28th, 2011, 02:21

Would you be able to point me in the direction of either of those hopup units? Preferably on a Canadian site, but doesn't really matter,

Hightimes · April 28th, 2011, 02:29

www.airsoftparts.ca

SlippGun · April 28th, 2011, 02:41

I love how airsoftparts.ca is now the answer to everything, when they don't have a TM or ICS hopup (which is what was being discussed).

By aiming me there though, I am going to assume that since the CA hopup is the only MP5 one they carry, that it is adequate?

Hightimes · April 28th, 2011, 02:52

I think the TM hopup are shit to begin with... Plus there hard to find...
The CA fits...

Hightimes · April 28th, 2011, 02:55

If your hopup is fine, just get a tight barrel

What kind of mods are you doing..? Higher fps or just stronger internals..?

SlippGun · April 28th, 2011, 03:04

Well, from what I've read online the Broxa hopup unit wont take new barrels.

I just wanted to squeeze a bit more accuracy out of the gun, since shots go pretty much everywhere at 100ft. So, Tight bore, new hopup unit, and I was looking at getting the ARS AEG hop-up rubber.

I haven't tested the compression on the cylinder, piston, etc yet. But depending on how that is, and how it goes after taping, I may replace those.

Hightimes · April 28th, 2011, 03:10

I see, good luck

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

April 28th, 2011, 01:31	#1
SlippGun Trader rating Join Date: Sep 2009 Location: Winnipeg, MB	MP5 Hopup unit Hey all, I am planning on upgrading my Aftermath Broxa, and I've been reading on here to replace the hopup unit, bucking and barrel. My problem is, I can not for the life of me find a new hopup unit (since the stock one is not compatible with after market parts?). Everyone says to get a TM one, but I can't find one. I've come across a CA one, would that be okay to go with. Also, would it be better to pick up a Black Python 6.03mm TB, or a Madbul 6.01mm TB? Thanks if anyone can help with these slight road bumps. __________________ They seek him here, they seek him there, those damn Frenchies seek him everywhere. Is he in Heaven, is he in Hell? Oh damn, that Scarlet Pimpernel. Last edited by SlippGun; April 28th, 2011 at 01:35..

April 28th, 2011, 01:45	#2
cjboi Trader rating Join Date: Oct 2009 Location: manitoba	TM and ICS would work they're both the same... I thought broxa didn't come with a hop up __________________ how can you help someone else if they're not willing to help themselves.

April 28th, 2011, 02:21	#3
SlippGun Trader rating Join Date: Sep 2009 Location: Winnipeg, MB	Would you be able to point me in the direction of either of those hopup units? Preferably on a Canadian site, but doesn't really matter, __________________ They seek him here, they seek him there, those damn Frenchies seek him everywhere. Is he in Heaven, is he in Hell? Oh damn, that Scarlet Pimpernel.

April 28th, 2011, 02:29	#4
Hightimes Trader rating Join Date: Jul 2010 Location: Markham, Ontario	www.airsoftparts.ca __________________ TEAM (THC)

April 28th, 2011, 02:41	#5
SlippGun Trader rating Join Date: Sep 2009 Location: Winnipeg, MB	I love how airsoftparts.ca is now the answer to everything, when they don't have a TM or ICS hopup (which is what was being discussed). By aiming me there though, I am going to assume that since the CA hopup is the only MP5 one they carry, that it is adequate? __________________ They seek him here, they seek him there, those damn Frenchies seek him everywhere. Is he in Heaven, is he in Hell? Oh damn, that Scarlet Pimpernel.

April 28th, 2011, 02:52	#6
Hightimes Trader rating Join Date: Jul 2010 Location: Markham, Ontario	I think the TM hopup are shit to begin with... Plus there hard to find... The CA fits... __________________ TEAM (THC)

April 28th, 2011, 02:55	#7
Hightimes Trader rating Join Date: Jul 2010 Location: Markham, Ontario	If your hopup is fine, just get a tight barrel What kind of mods are you doing..? Higher fps or just stronger internals..? __________________ TEAM (THC)

April 28th, 2011, 03:04	#8
SlippGun Trader rating Join Date: Sep 2009 Location: Winnipeg, MB	Well, from what I've read online the Broxa hopup unit wont take new barrels. I just wanted to squeeze a bit more accuracy out of the gun, since shots go pretty much everywhere at 100ft. So, Tight bore, new hopup unit, and I was looking at getting the ARS AEG hop-up rubber. I haven't tested the compression on the cylinder, piston, etc yet. But depending on how that is, and how it goes after taping, I may replace those. __________________ They seek him here, they seek him there, those damn Frenchies seek him everywhere. Is he in Heaven, is he in Hell? Oh damn, that Scarlet Pimpernel.

April 28th, 2011, 03:10	#9
Hightimes Trader rating Join Date: Jul 2010 Location: Markham, Ontario	I see, good luck __________________ TEAM (THC)

MP5 Hopup unit

Upgrades & Modifications