August 20th, 2009, 18:28 | #1 |
Turok's front sight removal thread
Hey guys, i know the steps in removing the front sight based on my search on this forum, but how do u take off the hex screw near the sling when the sling is in the way??? Ive got a CA M15A4
Last edited by turok_t; August 23rd, 2009 at 20:11.. |
|
August 20th, 2009, 18:39 | #2 |
Tys
|
Knock out the pin that's holding the swivle sling loop in place...then undo the grub screw.
*pain in the ass isn't it? |
August 20th, 2009, 18:41 | #3 |
omg its such a pain in the ass.. i wish i can just give u my gun now
|
|
August 20th, 2009, 18:43 | #4 |
Tys
|
Not after the 50 threads you've started with each thing you've done to it...
Finish it yourself... (from end to end...you've only got questions about the flash hider to go...LOL ) |
August 20th, 2009, 18:44 | #5 |
Maybe making ONE thread where he can post any and all thoughts that come across his mind would be better.
|
|
August 20th, 2009, 18:46 | #6 |
Tys
|
LOL..."Turok_T's build...step by step walk through" thread. It might have actually worked out very nicely....you could answer questions by just saying, "Oh..to do that follow post #56-58 on Turok's thread..."
Jk'ing around... Tys |
August 20th, 2009, 18:52 | #7 |
haha u guys are funny.. and hiliarious.. As for Tys, I sent you a message. I actually removed the flash hider, removed the grub screw from the bottom of the front sight and hammered out the 2 pins. Im inspecting it to see whats next now..
|
|
August 20th, 2009, 18:58 | #8 |
yaaay! its out... ok, time to remove the RIS now
|
|
August 20th, 2009, 19:47 | #9 |
Tys
|
If you want...when you're done...I'll take it completely apart down to the individual screws, put it into a bag and hand it back to you so you can do it all over again.
|
August 20th, 2009, 20:43 | #10 |
Lol, ure mocking me eh? I will be clueless on how to put it back together. But guess what? I managed to take out the RIS now Now, i need to figure how out to remove this delta ring and the outer and inner barrel
|
|
August 20th, 2009, 21:45 | #11 |
OMG, i give up trying to remove the delta ring.. i scratched some of the teeth already.. theres no way to remove it unless if i have the proper tool i tried ever tool including vise grips
|
|
August 21st, 2009, 00:58 | #12 |
after hours, i got the damn thing off with just a screwdriver and a hammer.. i hammered on one of the teeth CCW and it got loose.
|
|
August 21st, 2009, 09:12 | #13 |
aka coachster
|
could have gotten it off in seconds with a large pair of channel locks and a rag.
one of the mods should just call this "turok_t's AEG demolition - how to?" thread. |
August 23rd, 2009, 00:59 | #14 |
Turok_t's latest demolition problem:
Okay, so i installed a new rubber bucking and nub and new inner barrel on my CA M15A4. Im trying to put the upper receiver back on the lower receiver, but the metal plate that is supposed to slide in the ejection port (right next to the hop up) keeps on sliding back and forth when i assemble both parts of the reciever together. Here is a pic: The silver plate is the thing im referring to. How do I stabilize the plate so it doesnt wiggle when i put both parts of the receiver together? |
|
August 23rd, 2009, 01:43 | #15 |
Nevermind! i fixed it!
|
|
|
Bookmarks |
Thread Tools | |
|
|