PDI parts in a VSR-10 clone

TheGitFinger · March 5th, 2011, 17:34

Hey,

Hello people of ASC. I do need expert help with a certain issue of mine involving the TSD SD-700 clone that I own.

Unsurprisingly, it's broken.
The sears have worn down and my cylinder is scratched up + my spring is broken.

I would like to purchase some upgrades for my rifle. Will they fit?
1. reinforced V trigger system with piston end -$175-PDI
2. Bore up premier cylinder set-$200-PDI
3. 140 spring for vsr-10- $17-PDI

If i get the 140 spring, these internals will last a long time, correct?

Here is the links from airsoft GI, (will these get through customs?) I have successfully purchased from this site before.

http://www.airsoftgi.com/product_inf...oducts_id=6066

http://www.airsoftgi.com/product_inf...oducts_id=6663

http://www.airsoftgi.com/product_inf...oducts_id=6061

Help much appreciated,
Thegitfinger

moto · March 5th, 2011, 17:48

The parts will fit but...

The bore-up cylinder set requires the bore-up v-trigger. You will also have to remove the two guide rings in your reciever for the bore-up cylinder to fit (no biggie).

You will need a 13mm spring with the PDI cylinder kits. I cannot tell from that link if that spring is 13mm or 11mm.

If you use a 500mm or less inner barrel, a regular bore cylinder kit will be fine. Any more than that and a bore-up kit is suggested.

The parts should last a long time with a 140 spring... or even more for that matter.

Ive imported a number of the kits, trigger and springs. Never an issue.

SniperSam · March 5th, 2011, 22:26

Dont forget about the clone hop up rubber which will be crap ^^

Firefly is the answer mon ami, hard type for 410+ FPS, soft type for 390- FPS

And PDI are the way to go, PDI upgrades are best upgrades. Which will take basic handy man skills to do it all, but it's doable.

Honestly, the amount of money you'll be spending would be roughly the equivalent of buying a stock TM VSR10

TheGitFinger · March 8th, 2011, 21:39

well, the gun is a TSD Sd700 if that helps. I am not sure of the stock measurements. Just out of curiosity, if I buy a new clone (much cheaper) and downgrade the stock spring (too hot), will it last longer even with stock parts?

TheGitFinger · March 13th, 2011, 23:08

Bump

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

March 5th, 2011, 17:34	#1
TheGitFinger Trader rating Join Date: Mar 2011 Location: Toronto, Ontario	PDI parts in a VSR-10 clone Hey, Hello people of ASC. I do need expert help with a certain issue of mine involving the TSD SD-700 clone that I own. Unsurprisingly, it's broken. The sears have worn down and my cylinder is scratched up + my spring is broken. I would like to purchase some upgrades for my rifle. Will they fit? 1. reinforced V trigger system with piston end -$175-PDI 2. Bore up premier cylinder set-$200-PDI 3. 140 spring for vsr-10- $17-PDI If i get the 140 spring, these internals will last a long time, correct? Here is the links from airsoft GI, (will these get through customs?) I have successfully purchased from this site before. http://www.airsoftgi.com/product_inf...oducts_id=6066 http://www.airsoftgi.com/product_inf...oducts_id=6663 http://www.airsoftgi.com/product_inf...oducts_id=6061 Help much appreciated, Thegitfinger

March 5th, 2011, 22:26	#3
SniperSam Trader rating Join Date: Sep 2010 Location: Edmonton, AB	Dont forget about the clone hop up rubber which will be crap ^^ Firefly is the answer mon ami, hard type for 410+ FPS, soft type for 390- FPS And PDI are the way to go, PDI upgrades are best upgrades. Which will take basic handy man skills to do it all, but it's doable. Honestly, the amount of money you'll be spending would be roughly the equivalent of buying a stock TM VSR10 __________________ Proud Member of the Strelok society Whoa guy with the thumb rings, save some pussy for the rest of us Welcome to Bed Bath and Beyoncé, if you find anything you like, put a ring on it. What idiot called them Black Bears instead of African Abearicans

March 5th, 2011, 17:48	#2
moto Trader rating Join Date: Jun 2006 Location: Petawawa, Ontario	The parts will fit but... The bore-up cylinder set requires the bore-up v-trigger. You will also have to remove the two guide rings in your reciever for the bore-up cylinder to fit (no biggie). You will need a 13mm spring with the PDI cylinder kits. I cannot tell from that link if that spring is 13mm or 11mm. If you use a 500mm or less inner barrel, a regular bore cylinder kit will be fine. Any more than that and a bore-up kit is suggested. The parts should last a long time with a 140 spring... or even more for that matter. Ive imported a number of the kits, trigger and springs. Never an issue.

March 8th, 2011, 21:39	#4
TheGitFinger Trader rating Join Date: Mar 2011 Location: Toronto, Ontario	well, the gun is a TSD Sd700 if that helps. I am not sure of the stock measurements. Just out of curiosity, if I buy a new clone (much cheaper) and downgrade the stock spring (too hot), will it last longer even with stock parts?

March 13th, 2011, 23:08	#5
TheGitFinger Trader rating Join Date: Mar 2011 Location: Toronto, Ontario	Bump

PDI parts in a VSR-10 clone

Upgrades & Modifications