FG Airsoft Steel Nozzle WE M4 GBBR

[cav.]

Hay guys, I was looking around the internet and found this little guy:


http://fg-airsoft.com/en/parts-for-w...-ghk-pdw-.html
http://youtu.be/z-hpth7Fx94

It's a steel nozzle for WE M4 GBBR, with easy to adjust NPAS. Has anyone purchased this? It looks quite nifty and much more stable FPS wise than the RA-Tech nozzle and NPASinstalled! jJust really, really expensive >_>

[siggypoo]

Wouldn't that wear down your non-steel stock components super fast? Get that, and you have to upgrade all else that comes in contact with it, wouldn't you?


Location: YYZ VOR 062 radial, 17.5 DME FL5280

[▼Stripes▲]

I heard a lot of people had issues even with the aluminum ones wearing down the chamber ( I also heard a steel chamber was in development, but I've been off the forums for some time now)

[cav.]

Probably wear down the stock hop-up chamber. I might give this a try as I already have the steel hop-up chamber >_>

[Thenooblord]

also will not work with new manufacture WE M4s, they have a longer nozzle and slightly different hopup, this nozzle wont push the BB in far enough

that is unless its just cause the MODEL of M4 i bought was new and they didnt retroactively upgrade the regular lines? i could be wrong, but mine has the new style hopup and nozzle

[cav.]

Originally Posted by Thenooblord

also will not work with new manufacture WE M4s, they have a longer nozzle and slightly different hopup, this nozzle wont push the BB in far enough

that is unless its just cause the MODEL of M4 i bought was new and they didnt retroactively upgrade the regular lines? i could be wrong, but mine has the new style hopup and nozzle

There be new ones? Got a picture?

[Thenooblord]

old


new


new hopups have a little airseal ring and a flat hop style nub and are actually extremely good, i havent needed to upgrade any of them, all of my new WEs have had them since the MSK, even the tokarev, so I assume everything they make now uses it
the barrel is also cut differently from regular VSRs, though you can make a VSR barrel fit it by cutting it down a bit
if you wanted to use this FG nozzle you would have to buy a conventional barrel and hopup rubber both, as neither will work with the originals if you try to mix it

[cav.]

Oooo very interesting...that is good to know

Originally Posted by Thenooblord

old


new


new hopups have a little airseal ring and a flat hop style nub and are actually extremely good, i havent needed to upgrade any of them, all of my new WEs have had them since the MSK, even the tokarev, so I assume everything they make now uses it
the barrel is also cut differently from regular VSRs, though you can make a VSR barrel fit it by cutting it down a bit
if you wanted to use this FG nozzle you would have to buy a conventional barrel and hopup rubber both, as neither will work with the originals if you try to mix it

[MultipleParadox]

Interesting...
Not sure use the difference between those two nozzles though??

That said, the steel chamber as been out for a while now, got one in my m4, with ratech steel carrier and aluminum nozzle. Can't talk about performance or reliability yet though, haven't got to try it out "for real". Initial tests weren't impressive but I think my hopup was close to off and BB were rolling out

This nozzle seems to give relatively consistent results though

[Thenooblord]

Originally Posted by MultipleParadox

Interesting...
Not sure use the difference between those two nozzles though??

That said, the steel chamber as been out for a while now, got one in my m4, with ratech steel carrier and aluminum nozzle. Can't talk about performance or reliability yet though, haven't got to try it out "for real". Initial tests weren't impressive but I think my hopup was close to off and BB were rolling out

This nozzle seems to give relatively consistent results though

look at the very front

[MultipleParadox]

Originally Posted by Thenooblord

look at the very front

Got it
Thanks