|
|||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
|
Thread Tools |
September 22nd, 2007, 19:57 | #1 |
Broken hop-up?
AEG: Stock, brand new CA G36k
I noticed BBs rolling out of the barrel after nearly each automatic burst. So I I gradually adjusted the hop-up higher and higher, but the BBs still rolled out. I took the gun apart and removed the mechbox so I could have a good look into the barrel. Unless my eyes are playing trick on me, I see no difference between no hop-up and hop-up cranked all the way up. While it's quite visible on my TM M4. It's like if there was no hop-up rubber. Maybe it's stuck? Or is the G36 hop-up chamber built differently? Before I start fiddling with the hop-up chamber, does anyone know where I could get a replacement one? |
|
September 22nd, 2007, 20:00 | #2 |
you lost your bucking (the smaller black thing) its a little small piece of rubber kinda circular that goes onto the hole that pushes the hopup rubber down |
|
September 22nd, 2007, 20:04 | #3 |
Take the opportunity to replace the lacklustre stock CA sleeve-nub combo with a superior aftermarket one.
__________________
"The Bird of Hermes is My Name, Eating My Wings to Make Me Tame." |
|
September 22nd, 2007, 20:20 | #4 | |
+1. This is a "gift repair", as you are replacing shoddy stock parts with cheap, high-quality aftermarket parts. Get a good hopup sleeve and bucking matched to your velocity.
__________________
Quote:
|
||
September 22nd, 2007, 21:01 | #5 |
Are there different types of sleeve and bucking or they are all the same for current AEGs models?
Maybe there was never a bucking in the first place in my G36...I don't think I could have lost it without ever taking the gun apart. Hell, I didn't even clean the barrel yet. |
|
September 22nd, 2007, 22:21 | #6 |
I use a Systema Bucking and that one's for anything under M120 and lower Velocity.
I've taken the hop up assembly quite forceably and it hasn't stretched out on me like the $3 Guarder bucking. But I'm planning on getting the Prometheous Air Seal one =\ You might wanna take a look at those |
|
September 22nd, 2007, 22:29 | #7 |
Alright, I got 2 bucking & sleeve units. The clear Guarder and the Prometheus soft type . To make it worth the shipping fees, I also got a Systema inner barrel.
|
|
October 1st, 2007, 09:59 | #8 |
if I lost the little tiny rubber part... and I have a game soon what I can take to remplace it temporary...
__________________
Primary: AKm, M4, Secondary: 1911 Support: M72, RPG7 [MTX] Team |
|
October 1st, 2007, 10:41 | #9 |
Official ASC Bladesmith
|
You can find a peice of wire the same size, that'll work at least until you get a replacement. When I first got my used and well worn CA M24, I found no bucking in there, so I improvised by putting a chuck of microphone cable dialectric (the part of the co-axial cable that separates the conductor from the shield), and that worked for me for a few months until I got my new rubber set.
|
October 1st, 2007, 11:38 | #10 |
ok thanks but if a take a wire to big what they can make... as effect
__________________
Primary: AKm, M4, Secondary: 1911 Support: M72, RPG7 [MTX] Team |
|
October 1st, 2007, 12:17 | #11 |
Official ASC Bladesmith
|
Just try to find one that isn't too hard (best to take the insulation only, use strippers to shed it from the conductor) and is about the same size, roughly 1/8" max and use it. If the wire you choose is too big, you could greatly overhop and not have any control over it.
|
October 1st, 2007, 20:48 | #12 |
id say if the gun still shoots on target use it for the next game and then find somthing...
|
|
October 1st, 2007, 21:39 | #13 |
well i just brought some new bucking but where exactly do you put the small rubber thing?
|
|
|
Bookmarks |
|
|