Airsoft Surgeon Glock Slide Getting Stuck

HaloSix4 · December 14th, 2010, 19:19

So today I received my Airsoft Surgeon Glock Slide, after installing everything, there was a problem The slide pulls back fine, but gets jammed going forward, it goes a bout 3/4 the way and jams up badly, I literally need a hammer to bash it forward, it will not move with out the hammer.

It seems to be getting jammed up around the back of the slide around the BBU. took the BBU out and it worked fine, but I can not pinpoint, were it is getting held up. I will try to get some pictures later on.

Thanks

audi_bhoy · December 14th, 2010, 19:54

You might want to search around these forums, I don't remember which section, but it has been discussed in the last months...

Edit: quick search got me to this thread:
http://www.airsoftcanada.com/showthr...ight=pgc+slide

HaloSix4 · December 14th, 2010, 19:58

Ya I have looked around, I can only find problems with the PGC kits.

HaloSix4 · December 14th, 2010, 21:43

I've now done some grinding to the Slide and the frame rails, and it has not changed anything.

juicy · December 14th, 2010, 22:27

Could be your BBU getting stuck on your hammer's bearing?

HaloSix4 · December 14th, 2010, 22:30

Well, I dropped the BBU back into a few other slides I have and they all are very smooth, and needed no Mods.

CDN_Stalker · December 14th, 2010, 22:30

And let me guess, the stock slide works perfectly, right?

HaloSix4 · December 14th, 2010, 22:38

The stock plastic slide cracked a while ago, I've been using a Guarder 17C Slide, for a while now.

CDN_Stalker · December 14th, 2010, 22:45

Ah. Your thread reminds me of the bullshit I had to deal with regarding the G&G threaded outer barrel, none of my slides worked with the barrel except the stock plastic one. And Airsoft Surgeon lost my respect the first try with them and their AS M23 380 kit, few of the parts fit my gun and also reduced the velocity by 1/3 (when it should have increased it by that amount). Also caused massive feeding and gas spewing issues.

HaloSix4 · December 14th, 2010, 22:48

Shit, that sucks, I hope this is not the same problem.

HKGhost · December 14th, 2010, 22:59

this isn't a Glock but it's the same idea on how to solve your issue (I hope). YouTube - Fitting metal slides to Marui airsoft 1911 pistols. Hope it helps

CDN_Stalker · December 14th, 2010, 23:02

I should have said the G&G threaded barrel was for one of my KSC G19s, of the two I had with metal slides, it didn't work with any, even after much troubleshooting and filing. But the AS kit I referenced was for my KSC MK23, should have put out ~380fps but came in about 60fps lower. But because it was internals and not a metal slide, I can't add in anything except I don't like AS stuff after the frist experience. Hell, my new recoil spring in the kit snapped in two just installing the damned thing! Compressed it while sliding it over the guide rod to pin it, it bent a bit and snapped.

HaloSix4 · December 14th, 2010, 23:09

Quote:

Originally Posted by HKGhost

this isn't a Glock but it's the same idea on how to solve your issue (I hope). YouTube - Fitting metal slides to Marui airsoft 1911 pistols. Hope it helps

Thanks I'll take a look at that, I'm hoping it is just a simple problem because I love the look of the Glock 21 Slide on it.

Thanks

HaloSix4 · December 15th, 2010, 00:27

Ah nothing in that vid helped unfortunately, right now the Slide feels nice and loose on the frame rails, but once you pull it back about an inch it locks up and will not go forward.

juicy · December 15th, 2010, 02:19

Loading nozzle getting stuck? Just thinking of what comes in contact with the whole slide assembly at around an inch of slide travel backward... IDK.

Spring guide/recoil spring maybe?

What outer barrel are you using?

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

December 14th, 2010, 19:19	#1
HaloSix4 aka Halo64 Trader rating Join Date: Jul 2007 Location: Omemee, ON	Airsoft Surgeon Glock Slide Getting Stuck So today I received my Airsoft Surgeon Glock Slide, after installing everything, there was a problem The slide pulls back fine, but gets jammed going forward, it goes a bout 3/4 the way and jams up badly, I literally need a hammer to bash it forward, it will not move with out the hammer. It seems to be getting jammed up around the back of the slide around the BBU. took the BBU out and it worked fine, but I can not pinpoint, were it is getting held up. I will try to get some pictures later on. Thanks

December 14th, 2010, 19:54	#2
audi_bhoy Trader rating Join Date: Mar 2009 Location: Trois-Rivières	You might want to search around these forums, I don't remember which section, but it has been discussed in the last months... Edit: quick search got me to this thread: http://www.airsoftcanada.com/showthr...ight=pgc+slide Last edited by audi_bhoy; December 14th, 2010 at 20:01..

December 14th, 2010, 22:30	#7
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	And let me guess, the stock slide works perfectly, right? __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

December 14th, 2010, 19:58	#3
HaloSix4 aka Halo64 Trader rating Join Date: Jul 2007 Location: Omemee, ON	Ya I have looked around, I can only find problems with the PGC kits.

December 14th, 2010, 21:43	#4
HaloSix4 aka Halo64 Trader rating Join Date: Jul 2007 Location: Omemee, ON	I've now done some grinding to the Slide and the frame rails, and it has not changed anything.

December 14th, 2010, 22:27	#5
juicy Trader rating Join Date: Nov 2009 Location: Richmond, BC	Could be your BBU getting stuck on your hammer's bearing?

December 14th, 2010, 22:38	#8
HaloSix4 aka Halo64 Trader rating Join Date: Jul 2007 Location: Omemee, ON	The stock plastic slide cracked a while ago, I've been using a Guarder 17C Slide, for a while now.

December 14th, 2010, 22:45	#9
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	Ah. Your thread reminds me of the bullshit I had to deal with regarding the G&G threaded outer barrel, none of my slides worked with the barrel except the stock plastic one. And Airsoft Surgeon lost my respect the first try with them and their AS M23 380 kit, few of the parts fit my gun and also reduced the velocity by 1/3 (when it should have increased it by that amount). Also caused massive feeding and gas spewing issues. __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

December 14th, 2010, 22:48	#10
HaloSix4 aka Halo64 Trader rating Join Date: Jul 2007 Location: Omemee, ON	Shit, that sucks, I hope this is not the same problem.

December 14th, 2010, 22:59	#11
HKGhost Trader rating Join Date: Nov 2009 Location: Mississauga, ON	this isn't a Glock but it's the same idea on how to solve your issue (I hope). YouTube - Fitting metal slides to Marui airsoft 1911 pistols. Hope it helps __________________ Please email me as I'm not on ASC too often. Custom Build \| Upgrades \| Repairs \| Maintenance Contact: ghostgunwork@gmail.com / Private Message

December 14th, 2010, 23:02	#12
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	I should have said the G&G threaded barrel was for one of my KSC G19s, of the two I had with metal slides, it didn't work with any, even after much troubleshooting and filing. But the AS kit I referenced was for my KSC MK23, should have put out ~380fps but came in about 60fps lower. But because it was internals and not a metal slide, I can't add in anything except I don't like AS stuff after the frist experience. Hell, my new recoil spring in the kit snapped in two just installing the damned thing! Compressed it while sliding it over the guide rod to pin it, it bent a bit and snapped. __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871 Last edited by CDN_Stalker; December 14th, 2010 at 23:05..

December 15th, 2010, 00:27	#14
HaloSix4 aka Halo64 Trader rating Join Date: Jul 2007 Location: Omemee, ON	Ah nothing in that vid helped unfortunately, right now the Slide feels nice and loose on the frame rails, but once you pull it back about an inch it locks up and will not go forward.

December 15th, 2010, 02:19	#15
juicy Trader rating Join Date: Nov 2009 Location: Richmond, BC	Loading nozzle getting stuck? Just thinking of what comes in contact with the whole slide assembly at around an inch of slide travel backward... IDK. Spring guide/recoil spring maybe? What outer barrel are you using?

Airsoft Surgeon Glock Slide Getting Stuck

Doctor's Corner