CTW ECU Flashing + no fire

masterduck · January 10th, 2015, 18:54

Alright guys, this thread goes together with a previous thread awhile ago...
Say. i had a suspected ECU burnt out awhile ago and today i finally got the replacement part.

Now when i switch to fire/auto and press down on the white ecu button, the blue led comes on, but the gun still wont fire.....

Any idea whats wrong?

thanks!

Ricochet · January 11th, 2015, 00:25

I'm not sure what you're saying. You've replaced the ECU and you're still getting the same issue?

Here's your system; computer, ECU/optics, switch/fire selector, motor. Let's say your gun is in safe and you connect a battery; if you put it in semi and give it a single trigger pull, and then you have a constant blinking light on your optics, then it's likely your motor. Does it intermittently fire once in awhile? If so, then it's likely your motor as well. Why do think it's the ECU?

masterduck · January 11th, 2015, 05:31

OPse. What I meant was after I replaced the ecu, my gun still won't Fire. However the good news is this time the blue led comes on when I press the white button on the ecu.

Ricochet · January 11th, 2015, 06:32

Okay, the white button is the trigger contact, I'm assuming you know that. Does the LED have a slow steady blink when you push it, does it come on and stay on, or does it just remain on while you're depressing it?

Also, the light would not come on at all with your old ECU? Or it is acting exactly the same?

It sounds like you either have a motor issue or a fire selector issue.

masterduck · January 11th, 2015, 13:57

Old ECU: No light, no spin; even when the trigger contact is pressed with fire selector set to fire.
New ECU: blue lights comes on and stays on as long as the trigger control is pressed with fire selector to fire. But still no spin when trigger is pressed.

best

kev

Ricochet · January 11th, 2015, 14:13

If I have to guess I'd say your fire selector board may be fried. Know anyone with a CTW or PTW or FCC, etc? Change out the fire selector and see if it changes anything.

First off, remove your grip, and turn motors commentator a few turns, and then see if it'll cycle once or twice. It could still be the motor. Try this a couple times, by just clicking the commutator over 3-4 clicks and then firing.

If it isn't an obvious fix then email CTW or a licensed dealer and see if this is a common issue. Do this before you cost yourself more money.

masterduck · January 11th, 2015, 14:45

Cool. Thanks dude, i will do just that and see.

FULLMETAL · January 11th, 2015, 15:21

I will recommend you to enter to the CTW users facebook group bud... You might get better answers for this issue.

When the light is flashing it can be because of different reasons I had an issue with the battery and I got the same (at least in my case low battery was the issue).

So maybe something is funky with your mosfet or the battery itself.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

January 10th, 2015, 18:54	#1
masterduck Trader rating Join Date: May 2011 Location: Edmonton	CTW ECU Flashing + no fire Alright guys, this thread goes together with a previous thread awhile ago... Say. i had a suspected ECU burnt out awhile ago and today i finally got the replacement part. Now when i switch to fire/auto and press down on the white ecu button, the blue led comes on, but the gun still wont fire..... Any idea whats wrong? thanks! Last edited by masterduck; January 10th, 2015 at 19:21..

January 11th, 2015, 00:25	#2
Ricochet How much sand CAN you fit in your vagina!? Trader rating Join Date: Feb 2008 Location: North Delta, BC (Greater Vancouver)	I'm not sure what you're saying. You've replaced the ECU and you're still getting the same issue? Here's your system; computer, ECU/optics, switch/fire selector, motor. Let's say your gun is in safe and you connect a battery; if you put it in semi and give it a single trigger pull, and then you have a constant blinking light on your optics, then it's likely your motor. Does it intermittently fire once in awhile? If so, then it's likely your motor as well. Why do think it's the ECU? __________________ I have developed a new sport called Airhard. Pretty much the same as Airsoft, except you have to maintain an erection... Last edited by Ricochet; January 11th, 2015 at 00:31..

January 11th, 2015, 06:32	#4
Ricochet How much sand CAN you fit in your vagina!? Trader rating Join Date: Feb 2008 Location: North Delta, BC (Greater Vancouver)	Okay, the white button is the trigger contact, I'm assuming you know that. Does the LED have a slow steady blink when you push it, does it come on and stay on, or does it just remain on while you're depressing it? Also, the light would not come on at all with your old ECU? Or it is acting exactly the same? It sounds like you either have a motor issue or a fire selector issue. __________________ I have developed a new sport called Airhard. Pretty much the same as Airsoft, except you have to maintain an erection...

January 11th, 2015, 05:31	#3
masterduck Trader rating Join Date: May 2011 Location: Edmonton	OPse. What I meant was after I replaced the ecu, my gun still won't Fire. However the good news is this time the blue led comes on when I press the white button on the ecu.

January 11th, 2015, 13:57	#5
masterduck Trader rating Join Date: May 2011 Location: Edmonton	Old ECU: No light, no spin; even when the trigger contact is pressed with fire selector set to fire. New ECU: blue lights comes on and stays on as long as the trigger control is pressed with fire selector to fire. But still no spin when trigger is pressed. best kev

January 11th, 2015, 14:13	#6
Ricochet How much sand CAN you fit in your vagina!? Trader rating Join Date: Feb 2008 Location: North Delta, BC (Greater Vancouver)	If I have to guess I'd say your fire selector board may be fried. Know anyone with a CTW or PTW or FCC, etc? Change out the fire selector and see if it changes anything. First off, remove your grip, and turn motors commentator a few turns, and then see if it'll cycle once or twice. It could still be the motor. Try this a couple times, by just clicking the commutator over 3-4 clicks and then firing. If it isn't an obvious fix then email CTW or a licensed dealer and see if this is a common issue. Do this before you cost yourself more money. __________________ I have developed a new sport called Airhard. Pretty much the same as Airsoft, except you have to maintain an erection...

January 11th, 2015, 14:45	#7
masterduck Trader rating Join Date: May 2011 Location: Edmonton	Cool. Thanks dude, i will do just that and see.

January 11th, 2015, 15:21	#8
FULLMETAL Trader rating Join Date: Jun 2010 Location: Montreal	I will recommend you to enter to the CTW users facebook group bud... You might get better answers for this issue. When the light is flashing it can be because of different reasons I had an issue with the battery and I got the same (at least in my case low battery was the issue). So maybe something is funky with your mosfet or the battery itself. Last edited by FULLMETAL; January 11th, 2015 at 15:30..

CTW ECU Flashing + no fire

Doctor's Corner